Remove Security Prompts On SE Phones
Cute Girl • onIt & Systems 9 years ago • 5 min read

Sign your java midilets and remove all the security prompts on SE phones: Warning: This tut deals wid breaking into the phone's file system. Doing so will void ur warranty. If u dunno what u are doing, DO NOT proceed. Nobody can be held responsible if something goes wrong. Also please backup everything stored in ur phone before proceeding (files, contacts, organiser, sms everything!) u may take a backup of ur data wid this software, My Phone Explorer:

Download these files. These are the tools you'll need - XS++, USB Flash and FAR manager. Unpack all the files in resp. folders.


ace the far manager in C:\Program files only! goto C:\program files\far\plugins\sepp and double click on sepp.0.10.51patch.exe. It'll run command prompt and patch certain files.

Step1: Download these two files and extract to separate folders:

Step2: Install the usb flash driver.Turn off ur phone. Remove SIM and memory card and re-insert battery. Do not turn ON.

Now open the program XS++ . Click START. While pressing and holding the ‘c’ button on ur fone’s keypad, insert USB cable. Windows will detect a new hardware and ‘Install new hardware’ wizard pops up. Release the ‘c’ button. In the wizard, click ‘no, not at this time’ and next. Choose to install from a specified location and click next. Under ‘search for the best drivers to install’, check ‘include this location in the search’. Under ‘browse’, choose the path to the unpacked folder of USB Flash Driver. Now click next and let the windows install the driver. After installing the driver, close XS++ and disconnect phone and turn it off in case it has switched on. Remove battery for 2 seconds and re-insert it (to refresh your phone). if usb driver is already installed, this step can be skipped.

Step3: Break into ur phone using the breaker thru XS++. Again open XS++, click START and insert cable while pressing ‘c’ the same way as before. Ur fone gets detected and on the left side of the screen, u get the detailed info of ur phone including the EROM CID number, IMEI, firmware etc. IMP: the term RED should appear in the screen for u to continue the tut.

Check the Flash MAIN. Now browse(‘…’) to FAR manager folder and goto Plugins folder. Select the file ‘k750w800r2edcu.49r.ssw’ as MAIN file and hit flash (for cid49 phones and k750....dcu.36r.ssw for cid 36 phones). This will take 3 seconds. Unplug fone and close XS++ when it displays ‘Finishing Flash’. Take out and re-insert battery to refresh.

Now open FAR manager program, and press F11 key, select the SEFP plugin. in the following popup window, select DCU-60 cable, speed:921600 and boot script as K750w800cid49 (for cid 49 and K750w800CID36 for cid36 phones). Now click ‘Enter the Matrix’. In the following window, it asks you to connect fone just the way u connected to XS++ (by holding ‘c’ etc.)

Step4: FAR will detect ur phone and 2 folders will appear, FLASH and FS. Double click on FS and let it process for a couple of minutes. The folders on the left side of the FAR manager screen represent ur phone’s filesystem (FS). The right side of the screen displays the FAR manager folder (on ur PC's hard drive).

On the right side (on ur PC's hdd) navigate to the folder where the is unpacked. And on the left side (in the phone's FS) goto the folder: tpa/preset/custom. Copy both files customize_upgrade.xml and Halmer.cer from ur hdd to the folder on the left (tpa/preset/custom).

Exit FAR Manager. Remove the cable and replace the battery after 5 secs.

Step5: The hacking part is done! Now unload the breaker firmware. Again open FAR, connect phone the same way as udid before until u reach the screen that displays FLASH and FS folders. This time, double click on FLASH. Now double click ‘memory’. On the right side (hard drive) inside FAR folder, goto folder Plugins>REST. Look for the file named ‘RESTW700R1CA021’. Select and drag the file to anywhere on the left side of the screen and click on ‘copy’ and then ‘flash’. In the following popup click ‘close’. Close FAR and unplug fone. unplug and replace the battery after 5 secs.

This is a one time procedure and u needn't do it after the initial time.

Step6: Now u need to sign the java midilets on ur PC before uploading it to the phone. In case u haf any java apps which nag u on ur phone, then get those .jar files on the PC. Goto the folder where was extracted. Double Click on EQHalmer.exe. It asks whether u wanna add Eqhalmer to the context menu. Press "a" and then enter. It adds and then exits.

Find the .jar file which u need to sign. Right click on it and select the "Halmer" option. EQhalmer will run and sign it and generate a .jad in the same folder wid the same name.

Step7: Now upload both the .jar and the .jad file to Phone>Others folder. Goto the phone's Others folder in file manager and select the .jad file (be sure NOT to selec the .jar file) and install it. Once installed, the java midilet will show "Never Ask" in the permissions menu. Set it to it and Enjoy the java app sans annoying permissions prompt!

Source: Resources complied from various SE sites: esato, se-nse, lasyk etc.

PS: As of now this will work on cid49 and lower phones whose FS can be accessed wid FAR widout much hassels.

Word of caution: Since the Halmer key is now made public and anyone can sign any midilet be sure to download and install only those .jar files from public sites that are trustworthy!



Login to add comments on this post.

  • Guest 9 years ago

    I really like this post. Thanks for this article, Anyone got any more info about it? I am now your blog' s rss follower. you are now in my bookmarks.

    For information on my own web applications thankyuo would I use the application i used the following web site

    İstanbul boğazını herkes duymuştur.Fakat onu yakından görmemiştir.Bu tekne turu sayesinde İstanbul'un gizli yerlerini keşfettim.Bu tekne turu her insanın ölmeden önce yapmak isteyeceği bir şey.Bu tekne turlarına katıldığında siz de gözlerinize inanamayacaksınız.